|
|
 |
dlw@dlwco.com
See all of our
products by downloading our Lines Sheet. |
|
|
|
|
|
|
Flow
Detection: Flow Detect 1000 |
|
The Flow Detect 1000 is a high
quality, industrial grade instrument that senses flow/no-flow
conditions of solids and powders in pneumatic pipelines, gravity
chutes and feeders. The solid state sensor unit is virtually
unaffected by humidity, ambient light, pressure, vacuum,
temperature, noise, electrical signals, non-metallic build-up or
dust. The control console is equipped with self-monitoring
features, LED readout, and separate time delay adjustments for
both flow and no-flow conditions. We're confident you'll find
the Flow Detect 1000 to be the right choice for reliable flow
detection!
Features
- Reliable Doppler technology
- Can indicate flow/no flow
conditions of solids and powders in pipelines, chutes, and
feeders
- Non-intrusive flush mounting
senses through non-metallic surfaces
- Non-contact operation
eliminates flow stream interruption and equipment wear
- Control settings can be made
without accessing the remote sensor probe
- Fail-safe power protection
and loop fault monitor
- "Quick Set"
selectable, single turn calibration
- Explosion proof design
|
|
Specifications:
Remote Sensor Probe FDS1000
|
| Enclosure: |
Aluminum, Urethane
Powder Coat, NEMA 4X |
|
Power
Requirement: |
Provided
By FDC1000 Control Console, Low Voltage |
| Operating
Temperature: |
-22°
to +158°F (-30° to +70°C) |
|
Process
Temperature Max: |
+250°F
(+121°C)
If Ambient Air Temperature Is Below +150°F (+65°C) |
| Process
Seal: |
TFE Teflon |
|
Process
Connection: |
1
¼" NPT (flush mount with half coupling) |
| Conduit
Connection: |
¾" NPT |
|
Detection
Range: |
Up
To 10' Depending On Target |
| Interconnect
Wiring: |
5 Conductor Cable to
FDC1000 Control Console |
|
Indicators: |
Green
LED - Power
Red LED - Loop Current |
| Emission: |
24.125 GHz, Less
Than 1mW/cm2
(OSHA limit is 10mW/cm2) |
|
Approvals: |
Intrinsically
Safe When Connected To FDC1000 Control Unit, Class II, Groups E,
F & G, FCC Part 15 Certification |
Specifications:
Control Console FDC1000
|
| Enclosure: |
8" x 6" x 4"
Fiberglass, NEMA 4X, 12, 13 Flange Mount |
|
Power
Requirement: |
115 VAC, 60/50 Hz, 5VA
(230 VAC available)
|
| Operating
Temperature: |
-31° to +158°F
(-35° to +70°C) |
|
Output: |
DPDT Dry
Contacts, 5A @ 240 VAC, or 30 VDC |
| Indicators: |
Green LED - Power
Red LED - Loop Fault
Yellow LED - Sense Flow
Red LED - Alarm |
|
Interconnect
Wiring: |
5 Conductor
Cable to FDS1000 Sensor, Intrinsically Safe |
| Alarm Fail-Safe: |
Switch Selectable FLOW or NO
FLOW |
|
Time
Delay: |
FLOW delay,
Single Turn, 0.1 - 15 Seconds
NO FLOW delay, Single Turn, 0.1 - 15 Seconds |
| Sensitivity
Adjustment: |
High/Low Selectable, Single-turn
Adjustment |
|
Approvals: |
Ordinary
Locations, Industrial Control Equipment
Intrinsically Safe Output to FDS1000 Sensor |
|
|
|
| |
|
|
